Here you will find drawings, specifications, descriptions and PDF documents for Thin Panel Metal Wall Products from ROC INC.
If you don't see what your looking for, just ask.
Ultra-Rib structural exposed fastener roof and wall system.
• 26 gauge industrial quality steel or AZ50 (painted) and AZ50 (unpainted) coatings
• Full 36" coverage
• Purlin bearing leg
• Minimum roof pitch 1:12
• All orders custom cut to lengths up to 40'
• Perfect for commercial and industrial applications
• Aluminum available on an inquiry basis
Ultra-Rib structural exposed fastener roof and wall system.
• 26 gauge industrial quality steel or AZ50 (painted) and AZ50 (unpainted) coatings
• Full 36" coverage
• Purlin bearing leg
• Minimum roof pitch 1:12
• All orders custom cut to lengths up to 40'
• Perfect for commercial and industrial applications
• Aluminum available on an inquiry basis
An industry standard—Ideal for heavy industrial and lagging applications.
• Available mill finish, clad or painted in .032", .040" and .050" aluminum • Available in 24, 22 & 20 gauge steel, 32" coverage
• Panels can be curved
• Minimum slope for steel roofing applications is 21/2:12
• Standard lengths: 6'-45'
• 8" Rib available on an inquiry basis
• The allowable loads are based on 1986 AISI and 1986 Aluminum Association specifications.
• The allowable loads are based on stress only.
• The allowable loads for the steel load table may be increased by 1/3 for wind loading. The allowable loads have been increased for the aluminum load tables by 1/3 for wind loading. • The use of steel 4" Rib panels on roof pitches less than 2 1/2":12 (12°) is not recommended.
• The maximum individual panel length for steel 4" Rib on roofs in 32' due to thermal movement considerations.
• The use of aluminum 4" Rib panels on roofs is not recommended.
The Deep Rib II panel shall have a coverage of 30" for steel and 40" for aluminum". Rib height shall be 2". Panels shall be directly fastened to the substrate. The panel shall have a overlapping sidelap feature.
• Can be used for both wall and roof applications
• Available in 22 and 18 gauge steel
• Available in .032", .040" and .050" aluminum (43-7/8" panel with 40" coverage)
A bold rib design, perfect for horizontal and vertical applications. Large 4" deep ribs provide excellent strength and spanning capacity. Can be used inverted for roof applications. Minimum roof slope: 1:12. Excellent for applications with large spans between structural framing members. Standard lengths: 6'-45'
• The Deep Rib IV panel shall have a coverage of 24". Rib height shall be 4".
• Panels shall be directly fastened to the substrate.
• The panel shall have a overlapping sidelap feature.
A classic design with 7.2" rib spacing. Excellent strength and spanning capability. Excellent for both wall and roof applications.
• Available in .032" and .040" aluminum
• Available in 24, 22, 20 and 18 gauge steel
• Panels can be curved
• Minimum slope for roofing applications is 2:12
• Standard lengths: 6'-45' • 36" wide weather coverage
• Diaphragm capacity per ICBO Evaluation Report
• Classic mechanical seamed trapezoidal panel design
• Designed for low slope industrial applications
• Ideal for high performance Pre-Engineered Metal Buildings
• 3" nominal seam height - 24" seam centers
• 180 and 360 degree seaming available
• Factory applied sealant standard
• Concealed clip allows for thermal movement
• Normally installed over open framed structures
• Classic engineered snap-together trapezoidal panel design
• Designed for low slope industrial applications
• Ideal for Pre-Engineered Metal Buildings and Mini Storage Structures
• 3" nominal seam height - 24" seam centers
• Factory applied sealant standard
• Concealed clip allows for thermal movement
• Normally installed over open framed structures
The Mighti-Rib PBR panel shall have a coverage of 36". Panels shall be directly fastened to the substrate. The panel shall have an overlapping sidelap feature.
• Excellent for commercial and industrial applications
• 26 gauge full hard (80 ksi) steel
• Diaphragm capacity per ICBO Evaluation Report
• Standard lengths: 6'-45'
• PBR panels require a minimum slope of 1:12
• UL90 rating for PBR panels when attached to steel purlins
• Available unpainted or finished with high-performance Super Alurite® paint system
The V-Beam panel shall have a coverage of 32" for steel and 42 aluminum. Rib height shall be 1¾". Panels shall be directly fastened to the substrate. The panel shall have a overlapping sidelap feature.
• Minimum slope for roofing applications is 2:12
• Available in .040" and .050" aluminum
• Excellent strength and spanning capability
• Diaphragm capacity per ICBO Evaluation Report
• Standard lengths: 6'-45'
S E L E C T S E R I E S 1 2
• Classic concealed fastener flush panel design
• Ideal for long spanning walls, equipment screens, fascias and/or soffit applications
• Aesthetically pleasing for architectural, commercial and industrial applications
• 1 1/2" depth is stronger and spans greater distances than 1" panels
• Various stiffening bead patterns can be mixed and matched for multitudes of aesthetic designs
• Profile can be used with Select Series 612 panel variation for additional aesthetic designs
• Concealed fastened panel utilizing a screw flange requires no panel clips
• Panel ends can be swedged for end laps*
• Factory applied sealant is available
• Panels can be perforated upon special request
• .032" and .040" aluminum and 24, 22, and 20 gauge steel are available
S E L E C T S E R I E S 6 1 2
• Classic six up six down wall panel design
• Ideal for long spanning walls, equipment screens and/or soffit applications
• Aesthetically pleasing for architectural, commercial and industrial applications
• 1 1/2" depth is stronger and spans greater distances than 1" panel
• Profile can be used with Select Series 12 panel variation for additional aesthetic designs
• Concealed fastener panel utilizing a screw flange requires no panel clips
• Factory applied sealant is available
• Panel ends can be swedged for end laps*
• .032" and .040" aluminum and 24, 22 and 20 gauge steel are available
Factory formed, prefinished, lappable, exposed fastener, structural ribbed metal roof and wall system, that has been pretested and certified by manufacturer to comply with specified requirements under installed conditions.
Page Menu Items