ROC INC - Metal Wall and Roof Systems

(717) 823-6492

Commercial / Industrial Roof Panels

Here you will find drawings, specifications, descriptions and PDF documents for Commercial / Industrial roof panels from ROC INC.

Detail

2.5 SSR

Specifications

• Classic style with narrow batten seams
• Designed for longevity against rain, snow and wind •Concealed clip fastening system
• Easy installation
• Heavier gauges available
• May be disassembled without damaging panels on caps
• Minimum Roof Slope 1/2 :12
• Standard Lengths 6' to 51'

 

PDF

Back to Top

Panel Detail

4" Rib

Description

An industry standard—Ideal for heavy industrial and lagging applications

Specifications

• Available mill finish, clad or painted in .032", .040" and .050" aluminum
• Available in 24, 22 & 20 gauge steel, 32" coverage
• Panels can be curved
• Minimum slope for steel roofing applications is 21/2:12
• Standard lengths: 6'-45'
• 8" Rib available on an inquiry basis
• The allowable loads are based on 1986 AISI and 1986 Aluminum Association specifications.
• The allowable loads are based on stress only.
• The allowable loads for the steel load table may be increased by 1/3 for wind loading. The allowable loads have been increased for the aluminum load tables by 1/3 for wind loading. • The use of steel 4" Rib panels on roof pitches less than 2 1/2":12 (12°) is not recommended.
• The maximum individual panel length for steel 4" Rib on roofs in 32' due to thermal movement considerations.
• The use of aluminum 4" Rib panels on roofs is not recommended.

PDF

 

 

Back to Top

Detail

Deep Rib II

Description

The Deep Rib II panel shall have a coverage of 30" for steel and 40" for aluminum". Rib height shall be 2". Panels shall be directly fastened to the substrate. The panel shall have a overlapping sidelap feature.

Specifications

• Can be used for both wall and roof applications
• Available in 22 and 18 gauge steel
• Available in .032", .040" and .050" aluminum (43-7/8" panel with 40" coverage)

PDF

 

 

Back to Top

Panel Detail

Deep Rib IV

Description.

A bold rib design, perfect for horizontal and vertical applications. Large 4" deep ribs provide excellent strength and spanning capacity. Can be used inverted for roof applications. Minimum roof slope: 1:12. Excellent for applications with large spans between structural framing members. Standard lengths: 6'-45'

Specifications

• The Deep Rib IV panel shall have a coverage of 24". Rib height shall be 4".
• Panels shall be directly fastened to the substrate.
• The panel shall have a overlapping sidelap feature.

PDF

 

 

Back to Top

Panel Detail

Hefti-Rib

Description

A classic design with 7.2" rib spacing. Excellent strength and spanning capability. Excellent for both wall and roof applications.

Specifications

• Available in .032" and .040" aluminum
• Available in 24, 22, 20 and 18 gauge steel
• Panels can be curved
• Minimum slope for roofing applications is 2:12
• Standard lengths: 6'-45' • 36" wide weather coverage
• Diaphragm capacity per ICBO Evaluation Report

 

Back to Top

Panel Detail

IP Seam 3

Specifications

• Classic mechanical seamed trapezoidal panel design
• Designed for low slope industrial applications
• Ideal for high performance Pre-Engineered Metal Buildings
• 3" nominal seam height - 24" seam centers
• 180 and 360 degree seaming available
• Factory applied sealant standard
• Concealed clip allows for thermal movement
• Normally installed over open framed structures

 

Back to Top

Detail

IP Snap 3

Specifications

• Classic engineered snap-together trapezoidal panel design
• Designed for low slope industrial applications
• Ideal for Pre-Engineered Metal Buildings and Mini Storage Structures
• 3" nominal seam height - 24" seam centers
• Factory applied sealant standard
• Concealed clip allows for thermal movement
• Normally installed over open framed structures

PDF

 

 

Back to Top

Panel Detail

Mighti-Rib

Description

The Mighti-Rib PBR panel shall have a coverage of 36". Panels shall be directly fastened to the substrate. The panel shall have an overlapping sidelap feature.

Specifications

• Excellent for commercial and industrial applications
• 26 gauge full hard (80 ksi) steel
• Diaphragm capacity per ICBO Evaluation Report
• Standard lengths: 6'-45'
• PBR panels require a minimum slope of 1:12
• UL90 rating for PBR panels when attached to steel purlins
• Available unpainted or finished with high-performance Super Alurite® paint system

PDF

 

 

Back to Top

Panel Detail

V-Beam

Description

The V-Beam panel shall have a coverage of 32" for steel and 42 aluminum. Rib height shall be 1¾". Panels shall be directly fastened to the substrate. The panel shall have a overlapping sidelap feature.

Specifications

• Minimum slope for roofing applications is 2:12
• Available in .040" and .050" aluminum
• Excellent strength and spanning capability
• Diaphragm capacity per ICBO Evaluation Report
• Standard lengths: 6'-45'

PDF

 

 

Back to Top

Panel Detail

T-Rib

Description

The T-Rib panel shall have a width of 12", 14", 16", or 18" wide. Seams shall be 2½" high with a ½" top flange angled at 90 degrees from the seam to facilitate the seaming of the panel and cap. The panels shall have 1/16" x 1" stiffening ribs in the pan of the panel. Roof panels shall use a one-piece roof clip allowing for thermal movement of the panel system. The panel shall have a factory applied mastic and be mechanically seamed with a field operated electric seaming machine provided by the manufacturer. The panel system shall be as a true standing seam shape requiring no trapezoidal foam closures, plugs, or fillers at eaves. The maximum cap length shall be 30'.

Specifications

• A 21/2" high rib panel with excellent design flexibility
• Ease of installation for difficult hip, ridge, and valley conditions
• Mechanically seamed cap strip with factory- applied weatherstripping assures a weather-tight seam
• One-piece concealed clip allows for unlimited thermal movement
• Panels can be tapered
• Symmetrical design allows panels to be installed in either direction
• Multiple UL90 ratings for steel panels
• Can be installed over open framing or solid substrate
• Minimum roof slope: 1/2:12
• Standard widths: 16" and 18"

PDF

 

 

Back to Top

Panel Detail

Fabrib

Fabrib

Description

High quality aluminum panels are perfect for your light commercial, agricultural and confinement applications. For a long-lasting, low-maintenance building, choose Fabrib.

Specifications

• 0.014" (linear), 0.019" and 0.021" Thickness
• 9/16" Rib height
• 48" Coverage
• 2.67" Pitch
• Available in custom lengths up to 16'
• Lengths greater than 16' are not recommended due to expansion and contraction

Back to Top

 

 

Page Menu Items

 

Home | About ROC INC | Metal Wall and Roof Systems | Thin Panel Metal Wall Products | Thin Panel Metal Roof Products
Thin Panel Metal Wall and Roof Types
| Thin Panel Metal Wall and Roof Materials | Custom Fabrication | Sitemap | Contact ROC INC
2016 ROC INC All Rights Reserved
Web Design by Kendell Communication Service